Interface and Peripherals
Brand: e-Gizmo
A 4-channel bi-directional logic level translator is a device that converts voltage levels between different logic circuits, such as from 5V to 3.3V, or vice versa, while maintaining signal integrity.It features four independent channels, each capable of handling signals in both directions, allowing..
₱19.00
The USB-C Socket to SIP-4 Breakout Board is a compact and versatile adapter that allows you to easily interface a USB-C connection with a 4-pin SIP (Single Inline Package) header. Ideal for DIY projects, prototyping, and custom electronics, this breakout board offers a convenient way to convert USB-..
₱14.00
USB to TTL Converter based on the popular CP2102 USB Bridge chip.Power source: USB port (5VDC)Output Voltage: 3.3V TTL output levelAvailable i/o:- RX Receive input- TX Transmit output- DTR Data Terminal Ready outputNote: DTR output makes this suitable as an Arduino USB programming module...
₱95.00
- Chip type: W5500 - Supports both 3.3V & 5V. - Hardwired TCP/IP Protocols : TCP, UDP, ICMP, IPv4, ARP, IGMP, PPPoE - 10BaseT/100BaseTX Ethernet PHY embedded - Supports automatic response (full duplex / half duplex mode) - Supports 8 independent sockets simultaneously - Internal 32Kbytes Memory ..
₱288.00
Real time clock module based on DS1302Time keeping functions: Hours/Minute/Seconds and DateSRAM: 31 bytesInterface: 3-wire serial interfacePower supply Voltage: 2.0 to 5.5VDCBattery Backup: 3V CR2032 (Not included)Pin out:Vcc - +SupplyGNDCLK - Clock InputDAT - Data OutputRST - Reset Input..
₱53.00
The (Active Buzzer) with driver module uses a self-sounding buzzer and needs only a logic LOW drive to activate. It generates a fixed frequency sound, but you can produce various sound effects by modulating the control input on and off.Operating Voltage: 3.3V-5V DCControl input: Active-Low (compatib..
₱31.00
While it is fairly easy to DIY a 10/100BT POE injector, thanks to the 4 unused wires which can be readily used for the conversion, the same cannot be said when it comes to the gigabit port, since all 8 wires are in use to carry the data. Power delivery must be shared with a pair of data-carrying wir..
₱250.00
Brand: e-Gizmo
This module consists of three independent DAC channels with 8-bit Resolution and 0-Vcc voltage output. It has a wide range of operating voltage Vcc, which makes it logic compatible with popular computing platforms, such as Raspberry Pi and Arduino.Operation Voltage: 2.7V to 5.5VDAC Chip: ROhm BH2220..
₱110.00
This module allows your microcontroller module to connect to the RS485 bus of a system or device. RS485 is a robust industrial strength physical connection that allows high-speed serial data transfer over long wire runs.Operating Voltage: 3.3V to 5.0 VDCLogic Level: 3.3V or 5.0VDC depending on the p..
₱72.00
Single-channel Capacitive Touch Module with 4 modes of jumper selectable operation.Jumper pads are marked as "A" and "B".Mode of operations:A-open, B-open = Active high Touch-ON A-open, B-shorted = Active High Touch-ON Touch-OFFA-shorted, B-open = Active Low Touch-ON A-shorted, B-shorted = Active Lo..
₱12.00
Add a high-resolution Digital to Analog DAC converter channel to your microcontroller project-based using this module. It features a true 12-bit DAC based on MCP4725 chip. Connects to your host controller using I/O saving I2C bus. Has built-in EEPROM memory storage to keep your DAC settings on spot ..
₱99.00
This is one mystery module for advanced and adventurous experimenters. Other than being a timer module, we do not know anything more than that. We do not know how to operate or wire it. That is why we are selling it at a bargain.Each part is labeled with Chinese characters. It has a Flash microcont..
₱29.00